Manufacturer of Universal Device Programmers , Gang Programmers , EPROM Programmers , Flash / PIC Programmers , UV Erasers , CF duplicators

 

Home

Order Form

Contact Us

Download software

Feedback and Tech Support

 

 

 
 

 

                    NAND FLASH PROGRAMMER

 
Turbo NAND Flash Gang Programmer
Low Voltage (1.2V ~ 1.8V) / NAND Flash
LabTool-T400LabTool-T400 Turbo flash gang programmer is four sockets PC-based gang programmer. It features four independent isolated modules, extremely high speed in writing flash memory chip. It supports 3.3V, 2.7V, 1.8V and 1.2V chip in both VCC and VIO without low voltage converter and handles 8/16/32 bits flash chip in different package through adapter modules, up to 128Gb flash can be support ... (more)

Price: $1495.00  Single Socket / $3995.00 4 Socket
Features
bulletSupport 3.3V to 1.2V flash memory chip in VCC and I/O without low voltage converter.
bulletFlash chip support up to 128G bit.
bulletExtremely high speed: it blank check a 64M bit flash chip in 1.6 seconds, program the STM28W640CT (4 word programming algorithm) within 11.5 seconds, verify within 3.2 seconds.
bulletUSB interface: support USB 1.1 or 2.0
bulletOne PC can connect up to 16 unit Labtool-T400 to perform Asynchronous programming
bulletDevice insertion /continuity check before programming.
bulletTarget quantity and Max failure rate alarm.
bulletSupports Windows 98SE / ME / 2000 / XP / Vista(32bit) / 7(32bit / 64bit)
bullet1 year warranty
 
Introduction
bulletLabTool-T400 Turbo Flash Gang Programmer is four sockets PC-based Gang Programmer. It features four independent isolated modules, extremely high speed in writing flash memory chip. It supports 3.3V, 2.7V, 1.8V and 1.2V chip in both VCC and I/O without low voltage converter and handles 8/16/32 bit flash chip in different package through adapter modules, up to 128Gb flash can be support. The LabTool-T400 is an ideal programmer for customers in GSM, 3G Mobile, PDA, Internet router and others.
 
Unbeatable programming speed and throughput
bulletThe LabTool-T400 has build in Compact Flash Card (CF) on board that reduce the massive data transfer between the PC and LabTool-T400 .The LabTool-T400 performance reach the speed limitation of the chips in its spec. No other gang programmer today and future can beat the speed of the LabTool-T400.
 
LabTool-T400 performance ( PC with P4 1.3G 128M RAM)
   
STM 4 word algorithm
Intel EFP algorithm
Spansion word algorithm
    Blank check
1.65s per 64Mb
1.65s per 64Mb
1.65s per 64Mb
    Programming
11.5 sec per 64Mb
16.6s per 64Mb
29.5s per 64Mb
    Verify
3.2s per 64Mb
3.2s per 64Mb
3.2s per 64Mb
    Total
M28W640E in 16.3 sec
GE28F640W30B in 21.4 sec
Am29DL640G in 34.5 sec
 
3.3V to 1.2V chip in VCC and I/O support
bulletThe LabTool-T400 use the 90nm FPGA chip in hardware design, it can handle the chip from 3.3V to 1.2V in both VCC and I/O without need special low voltage converter circuit. This new technology fulfils customer's need and makes customer's investment fully protected.
 
High density chip support
bulletThe LabTool-T400 has reserved the growth potential in chip's density. It covers 8/16 bit flash today and future's 32 bit flash chip. Its I/O pin driver can cover flash with Max 128G bit in density. This growth potential protected customer's investment without purchasing a new generation programmer over a decade in future.
Expansion through USB Hub and configure as a Multi-station Asynchronous Gang Programmer
bulletThe LabTool-T400 interface with PC through USB interface, which support USB 1.1 and 2.0. If customer needs more units in production, just purchase extra LabTool-T400 and connect those LabTool-T400 through USB Hub, up to 256 LabTool-T400 can be attached to one PC. Recommend with 8-16 unit LabTool-T400 control by one PC to avoid performance decrease. Such configuration has significantly reduces the cost per station with low initial purchase cost and growth potential in future.
 
Adapter modules with ID
bulletThe LabTool-T400 adapter module has independent ID. After inserting the module in the LabTool-T400, the system will detect the module's ID and compare the corresponding adapter modules with the chip select in software. This future prevents the wrong adapter module insert or wrong chip selection in operation.
 
Specification
 
Device support
bulletFlash memory: include NOR , NAND, EEPROM and other flash technology
bulletDevice data width: 8, 16 and 32 bit
bulletMax flash density support: 512Mb with 128M byte Compact Flash Card install on board (standard offer), can be extend to 128Gb with exchange higher density Compact Flash Card on system hardware.
File format
bulletBinary, Intel Hex, Intel Ext Hex, Motorola S, HP64000 ABS, Straight Hex
 
Interface to PC
bulletAccept USB 1.1 or USB 2.0
 
PC system requirements
bulletOperating system: Windows 98SE/Me/2000 or Windows XP
bulletProcessor: Pentium and above
bulletMemory: 256M and above
bulletHard Disk: over 100M free space
bulletCD ROM driver
bulletInterface: USB 1.1 or 2.0 interface
 
General
bulletPower adapter: 65W AC 100-240/47-63HZ Auto Switch.
bulletOut put: DC (12V/3A, 5V/6A)
bulletOperation temp: 5 to 45 degree C
bulletSafety: CE&LVD certified
bulletShipment Weight: 5.0 Kg without modules.
Download the most update LabTool-T400 software for a trial.
 
LabTool-T400 All device list.
 User Manuals