|
| |
|
General Features
8 independent fully isolated 48-pin ZIF sockets
Support Flash, EPROM, EEPROM, Microprocessor with 5 Volts and 3 Volts
Program 8 pieces 8 MB Flash chips within 45 seconds
Auto-sense, self-start with standard/semi-concurrent mode
Independent modules allow flexible configuration
Universal adapters for 48TSOP/44PSOP/40TSOP Flash chips support .
BGA , EBGA , QFFP, TQFP
Customized MCU support
Project file save/load function
Print port interface with auto switch power supply
Supports Windows 95/98, Windows 2000 , Windows NT , Win XP, Vista,
Win 7 32 bit, Win 7 64 bit .
Software update via Internet
Connect to PC via USB or Parallel port
Optional handler interface
|
Technical Features:
The GangStar-Pro is a
USB based gang programmer. It features 8 pcs fully
isolated 48-pin ZIF sockets, extremely high throughput, standard 5V
and 3V chip support, device insertion and continuity check. With
PC-based design the device update through software gives customer
more flexible and quick access to the new chip support. The GangStar-Pro
supports EPROM, EEPROM, FLASH in the introduction. Future software
update will include 87C5x, 89C5x , and PIC16Cxx microprocessor.
The GangStar-Pro has flexible design. If customer has special chips
that not in our standard support list, we provide a special program
that allow the GangStar-Pro become a customize special chip
production gang programmer.
|
Technical Specifications
Unbeatable speed
through semi-concurrent programming technology
The GangStar-Pro’s on-board intelligence
reduces the system’s overhead. It programs 8 pcs of 8Mb flash chips
(Intel 28F800B3) within 45 seconds. An experienced operator can
program thousands of high density chips per day. Further more, with
the semi-concurrent programming capability, you can divide the 8
sockets into two groups and program one group of 4 chips while
removing or inserting the chips of the other group simultaneously.
| |
|
Flash Intel 28FXXX |
| |
2M |
4M |
8M |
16M |
| Blank Check |
3.9
sec |
7.1
sec |
13.8 sec |
27.2
sec |
| Program |
11.6 sec |
22.6 sec |
42.7 sec |
85.0 sec |
| Verify |
8.5 sec |
16.5 sec |
32.4 sec |
64.4 sec |
|
Fully isolated ZIF
socket
Each socket’s address, data bus, control
lines, power supply and programming voltage of GangStar-Pro are
isolated (> 1M ohm). Besides, each socket has independent build-in Vcc and Vpp current limit circuitry. A defective device will not
affect the programming integrity of other devices. |
Devices insertion and
continuity checks-No mistakes!
The GangStar-Pro performs device insertion
and continuity checking before program each device. It can detect
poor pin contact, device insertion of wrong position and pin number
mismatch. This function prevents the damage of expensive chip due to
operator’s mistake. |
Auto-sensing and
self programming
The GangStar-Pro has implemented a
patented technology: after the chips are put into the ZIF sockets,
GangStar-Pro will check if the chips are inserted properly and have
good contact. The system has an adjustable timer so that if the poor
insertion is not fixed in time, GangStar-Pro will shutdown the
socket of poor contact socket and program the rest of chips
automatically.
|
Project file "Save
and Load"
Customer can save a project file which
contains the device selection, buffer data and all programming
option settings. The project file can be loaded at any time for
future use. Engineer's design and settings can easily pass to
production department without mistake. |
Variable VCC with
one or two-pass verification
The GangStar-Pro allow you to set the
verifying voltage, e.g.,Vcc +/- 5%, Vcc+/- 10%, after chips are
programmed. Vcc voltage can be 2 Volts to 7.5 Volts. The data
retention is promised with this feature. |
Device Support
Summary
Generic EPROM: 27xxx series, 32k to 32Mb, 8/16-bit width.
Flash EPROM: support NOR. NAND, AND, DI-NOR, EEPROM technology.
29XXX, 5V/3V Flash, 28Fxxx 12V/5V/3V Flash from all major venders.
JMicroprocessor: (Future release through software update) Intel
87C5x compatible, ATMEL 89C5x compatible, Microchip PIC16Cxx.
Detailed Device List |
Universal Adapter for Flash chips
The GangStar-Pro
is designed to meet your future need of high density flash
chips, it uses PC’s resource to support 32k-bit up to 256M-bit
memory chips without upgrade the hardware. The GangStar-Pro
also provides 48-pin TSOP, 44-pin PSOP, 40-pin TSOP, and
32-pin TSOP universal adapters for all the flash chips which
eliminates the need to purchase multiple adapters and saves money. |
 |
Compact UV Eraser, Model-T6
$149.00
- 60 minute autoshut off
- 20 Minute Eraser time
- 5-15 devices depending on size
- Steel Enclosure Design
- Conventional ( non electronics) transformer
produces stronger output
- 110VAC or 240VAC power input
|
|
Manufacturer of Universal Device Programmers , Gang
Programmers , EPROM Programmers , Flash / PIC Programmers , UV Erasers , CF
duplicators 